Dale Moore Posted August 2, 2025 Report Posted August 2, 2025 Pulled the old bonnet and front wing off this morning in preparation for fitting the new bonnet. I remember, and the amount of mastic I discovered, confirmed the fit between the filler plate and inner wing was poor to say the least when I assembled this 25 yrs ago. Have the filler plates improved since then? If so, any favoured supplier? Dale Quote
Chilliman Posted August 2, 2025 Report Posted August 2, 2025 Stuart may well be able to point you in the right direction but the last ones I had were so bad I gave up & made my own which I've done a couple of times now....at least you end up with something bespoke that fits where it should. Quote
stuart Posted August 2, 2025 Report Posted August 2, 2025 I got a pair recently from TR shop and they were ok when compared with an original. Ive found often that the front panels have been previously repaired badly which then throws everything out anyway. Stuart. Quote
Dale Moore Posted August 2, 2025 Author Report Posted August 2, 2025 Thanks for heads up Stuart, although they don't seem to be listed on their website, I'll give them a call on Monday. I suppose the plates are not the most difficult part to make or alter and I can always use half a tube of mastic again. Dale Quote
stuart Posted August 2, 2025 Report Posted August 2, 2025 12 minutes ago, Dale Moore said: Thanks for heads up Stuart, although they don't seem to be listed on their website, I'll give them a call on Monday. I suppose the plates are not the most difficult part to make or alter and I can always use half a tube of mastic again. Dale TR Shop website is only a vague representation of their stuff, always best to ring and talk to them. FWIW often the front return of the wing where that little panel sits has also been repaired before hence the infill panel not fitting as well. Stuart. Quote
Dale Moore Posted August 2, 2025 Author Report Posted August 2, 2025 I had the wings restored by North Devon when I bought the car. I can't remember if that was an area that they worked on. It still looks pretty good though Quote
Malbaby Posted August 2, 2025 Report Posted August 2, 2025 I welded the filler panels onto the wings...being very careful with alignment to the curve, and face, of the outer front support panel. Quote
jerrytr5 Posted August 3, 2025 Report Posted August 3, 2025 Fit GRP inner wing shields & don't bother with the metal bits. Jerry Quote
stuart Posted August 3, 2025 Report Posted August 3, 2025 1 hour ago, jerrytr5 said: Fit GRP inner wing shields & don't bother with the metal bits. Jerry 11 hours ago, Malbaby said: I welded the filler panels onto the wings...being very careful with alignment to the curve, and face, of the outer front support panel. Thats what I do. Stuart. Quote
Jase Posted August 3, 2025 Report Posted August 3, 2025 1 hour ago, stuart said: Here you go Stuart. Thanks. Quote
Malbaby Posted August 3, 2025 Report Posted August 3, 2025 10 hours ago, Jase said: Do you guys have a picture of that? I do not have any pics as the wings are fitted...I stress the need to configure the filler panel to the front panel...This can be tricky...Both for contour and so that the grill will fit correctly. Quote
Dale Moore Posted August 4, 2025 Author Report Posted August 4, 2025 Out of stock at Tr Shop ATM, they hope to have some in by the weekend. I'm in no rush, and I can temporarily fit the wing to check the bonnet fit without the filler panel. Dale Quote
Dale Moore Posted August 4, 2025 Author Report Posted August 4, 2025 1 hour ago, Jase said: Could you not make them? Possibly could. See how it looks with the wing temporarily on. Just want to give myself the best chance for getting a better wing to bonnet fit than before Dale Quote
stuart Posted August 5, 2025 Report Posted August 5, 2025 12 hours ago, Jase said: Could you not make them? Bit of an awkward shape to get right and look nice. Stuart Quote
RogerH Posted August 5, 2025 Report Posted August 5, 2025 could be fabricated but not easy Roger Quote
Jase Posted August 5, 2025 Report Posted August 5, 2025 You could make it in three parts looking at the above photo and weld them together? Quote
Chilliman Posted August 5, 2025 Report Posted August 5, 2025 2 hours ago, Jase said: You could make it in three parts looking at the above photo and weld them together? Exactly what I did, never going to be as pretty as a single pressed unit .....but it can be made totally bespoke to fit perfectly & who the heck is ever going to know the difference when fitted? Quote
Malbaby Posted August 5, 2025 Report Posted August 5, 2025 23 hours ago, Dale Moore said: Possibly could. See how it looks with the wing temporarily on. Just want to give myself the best chance for getting a better wing to bonnet fit than before Dale In that case, I suggest fitting the wings and bonnet temporarily in their final position, before you fit/weld in the filler panel. Quote
Dale Moore Posted September 21, 2025 Author Report Posted September 21, 2025 (edited) Getting close to final fit before hinges and then off to paint. I've spent time in getting the front inner and outer wings in correct alignment to the bonnet when it's pressed evenly to the windscreen panel. It's pretty close now, but a little tweak needed to the front RHS corner of the bonnet to get it level with the tip of the chrome strip Edited September 21, 2025 by Dale Moore Quote
Malbaby Posted September 21, 2025 Report Posted September 21, 2025 (edited) 9 hours ago, Dale Moore said: Getting close to final fit before hinges and then off to paint. I've spent time in getting the front inner and outer wings in correct alignment to the bonnet when it's pressed evenly to the windscreen panel. It's pretty close now, but a little tweak needed to the front RHS corner of the bonnet to get it level with the tip of the chrome strip Are you planning to add metal to the bonnet to close the gap as in your top pic? Edited September 21, 2025 by Malbaby Quote
Dale Moore Posted September 22, 2025 Author Report Posted September 22, 2025 The bonnets is not quite positioned evenly in the pictures and needs to come over a bit to the nearside. The tip of the bonnet lines up better on that side, but when the drivers side is following the curve of the wing nicely it leaves the tip of the bonnet 1/4in high. Looking to take a small cut to the return on the bonnet, just to the left of the headlight and bend it down slightly. I think I will get away with 1/8in without anyone noticing. Dale Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.